{
  "status": "ROUTED_DIGITALLY_VERIFIED_QUOTE_REVIEW_NOT_PRODUCTION_RELEASED",
  "physical_copper_layers": 1,
  "empty_editor_layer": "B.Cu; never order a second copper layer from this editor declaration",
  "length_mm": 152.4,
  "width_mm": 9.2,
  "finished_flex_thickness_target_mm": 0.1,
  "nominal_copper_um": 35,
  "cut_lengths_mm": [
    25.4,
    50.8,
    76.2,
    101.6,
    127.0,
    152.4
  ],
  "retained_input_reference": "J1",
  "pad_length_mm": 3,
  "edge_margin_mm": 0.35,
  "lane_gap_mm": 0.2,
  "lanes": [
    {
      "pin": "1",
      "net": "V24_MOTOR2",
      "width_mm": 1.2,
      "y_mm": 0.95
    },
    {
      "pin": "2",
      "net": "GND",
      "width_mm": 1.2,
      "y_mm": 2.35
    },
    {
      "pin": "3",
      "net": "CAN_H",
      "width_mm": 0.5,
      "y_mm": 3.4
    },
    {
      "pin": "4",
      "net": "CAN_L",
      "width_mm": 0.5,
      "y_mm": 4.1
    },
    {
      "pin": "5",
      "net": "SPOT1_LED_PLUS",
      "width_mm": 0.55,
      "y_mm": 4.825
    },
    {
      "pin": "6",
      "net": "SPOT1_LED_MINUS",
      "width_mm": 0.55,
      "y_mm": 5.575
    },
    {
      "pin": "7",
      "net": "SPOT2_LED_PLUS",
      "width_mm": 0.55,
      "y_mm": 6.325
    },
    {
      "pin": "8",
      "net": "SPOT2_LED_MINUS",
      "width_mm": 0.55,
      "y_mm": 7.075
    },
    {
      "pin": "9",
      "net": "SPOT3_LED_PLUS",
      "width_mm": 0.55,
      "y_mm": 7.825
    },
    {
      "pin": "10",
      "net": "SPOT3_LED_MINUS",
      "width_mm": 0.55,
      "y_mm": 8.575000000000001
    }
  ],
  "termination_banks": [
    [
      "J1",
      3.0,
      null
    ],
    [
      "J2",
      23.0,
      25.4
    ],
    [
      "J3",
      48.4,
      50.8
    ],
    [
      "J4",
      73.79999999999998,
      76.2
    ],
    [
      "J5",
      99.19999999999999,
      101.6
    ],
    [
      "J6",
      124.6,
      127.0
    ],
    [
      "J7",
      149.99999999999997,
      152.4
    ]
  ],
  "components_to_purchase": [],
  "assumptions": {
    "motor_dc_A": 0.75,
    "spot_each_A": 0.3333333333333333,
    "currents_measured": false,
    "pcb_joint_motion": "none; ordinary wires at ends",
    "connector_footprints": "not in this narrow ribbon draft"
  },
  "pending": [
    "factory stack/coverlay/adhesive and copper minimum acceptance",
    "cut-edge treatment and solder-pad support trial",
    "short harness CAN signal and motor transient tests",
    "bonded temperature measurements",
    "optional wider connector ends decision"
  ],
  "name": "gimbal-static-v0.2",
  "coverlay_overlap_mm": 0.05,
  "stiffener": "0.20 mm PI plus adhesive on B under each solder bank, local X=center +/-2 mm, full ribbon width; no stiffener across marked cuts",
  "native_pcb_sha256": "7136c5c343da3194c0ada81330edd99336b3078152bb8f1ce47f5da158f2287d",
  "current_source": "This folder supersedes flex-drafts for quote geometry; physical fit/factory acceptance remain pending."
}